Interceptor Carrier Board

Software Q. How do I monitor/reset the PoE ports? A. Use the "PoE Ports" tab of the "System Settings" utility in the Axzez provided Wayfire, 3D Wayland Compositor. Q. How do I read the PoE controller status? A. $ cat /proc/pse1/status voltage: 47437 (40000-60000) mV current: 40 (2500) mA power all

Can the Interceptor board be run with any of the alternative compute modules like soquartz, CB1, Radxa? I'm pretty much giving up on ever getting a CM4 from a reputable source (been trying for over a year). Unless there's something else I can use in the board, I'll probably just toss it in my box of

Hello, I'm new to Raspberry, so please forgive me if I say stupid things :) I bought an Axzez Interceptor Board, and I've received from one of my friends a Raspberry CM4 with eMMC storage. On the Pi CM4 has been installed the following OS by my friend before to give it to me: =-=-=-=-=-=-=-=-=-=

Hello! I have my Interceptor board and CM4 installed in one of your five drive 1U server cases with powersupply! It's a great fit for this product and I love it. The only challenge I'm having is I can't get the NIC to stay on the assigned IP address in the config-rt*.sh file that is in /usr/libexe

I'm using a CM4 8/32 with an Interceptor Carrier Board and the 270W power supply in the 1U case with two 8TB HDDs. I've exchanged the 4 fans that were included in the case against 2 Noctua fans with lower power consumption and noise. The whole build consumes around 32W without load. With the HDDs in

HI, USB not booting. This thread isn't helpful because I used Debian and etcher to write the files: https://www.axzez.com/forum/interceptor-software-use/unable-to-boot-os-from-usb?origin=auto_suggest 1. how do I tell if usb is powered on? 2. if USB is not an option, do i have the option of load

Hello. I have an interecptor board, and I am planning to design and build an enclosure for it. Would you be able to provide any CAD files/dimension specifications to save me measuring everything manually? Thanks

I hooked up the power supply, hard disk ssd ,usb , and cm4 board it came with. I tested the power supply Seasonic s12-650 and it powered on with paperclip test. I was unable to hit jumper 3 and 4 on board next to sata0 to power it on. I used the picture of the cm4 on top of the board on the case t

Hi guys, I am using both interceptor baords as file servers in my home environment. all works fine, i just have not been able to backup the system on the cm4 module. I am using your software on a CM4 with eMMc storage, works fine. But if i stick the CM4 module in a CM4-IO-Base-A Module, I can not g

I've got a brand new interceptor board with an rPi CM4 and PoE board up and running, and I'm trying to understand better how the PoE ports connect to the system. What is the path from the PoE phy to the CPU? Do they connect to the realtek switch at all? It appears that the rtl8367rb has extra interf

I am slowly getting my interceptor set up here. I just installed the OS on a SSD and it seems to work well if I select "Boot sda1" from the menu. I am going to set this up as a headless system, so I would like to make this the default optoion. How do I change this? Thank you for your help.

We've put together a document to assist with the setup of your Interceptor System: https://www.axzez.com/Interceptor_System_Setup.pdf Let us know if you'd like to see clarification or missing information added.

Hey received my board, works a treat! but it never came with any mounting screws for the CM4, call this an oversight mostly on my part, also I definitely should have gotten the mounting board too, but I'm after direction on what and where I can get some since the CM4 is very easy to knock off of its

I managed to run the Interceptor on EMMC with "Alma Linux", i am curious, is it possible to boot from EMMC and place the root filesystem on a Satadrive? If yes, is there a good tutorial? I just found the standard USB-Sata-Drive stuff. Maybe i am doing it wrong, created a ext4 on sata and rsynced roo

Finally got parts in and did a little electronics origami. In case anyone is interested, my parts list are at the top of my GitHub how-to (work in progress as I proceed with software setup). The plan is to run OMV with MergerFS and SnapRAID. Primary use will be for over the network TimeMachine back

Software Q. Where can I download the latest Axzez Interceptor Operating System (OS) image? A. The custom Interceptor OS is available for download at: https://www.axzez.com/interceptor-os.img.gz See the Axzez Software Downloads page for more information. Q. How do I install the Axzez provided OS

Hello, I'm curious about the RS-485 connector on the Interceptor. What is it (could it be) used for ? I searched the forum for clues, but no luck. Thanks!

Which one is better? Booting and running you OS in usb or installing the OS on one of the sata with SSD? If I'm gonna use and run it with the usb boot, will it suffer performance penalties like transferring data to a SATA SSD drive? I am currently building it with your carrier using a CM4 lite, Tha

Moved my interceptor board into my NAS Case with 4 HDD Bays. When I booted, the Network would not work (all show "NO-CARRIER", and physical LEDs do not light up, neither on the interceptor board, nor on the network switch). Found the following in the kernel log: [ 13.529743] rtl8367b rtl8367rb:

Hello, I finally got a CM4 to populate my Interceptor. I am planning to build a small NAS using an old 4 bay SCSI enclosure with a 240W power supply. Since it only has 5 and 12V rails available, I was wondering if you had any data on typical and maximum draw on the 3.3V line in operation. I was thin

I have an AW9523 hooked up to one of the PoE ports and it seems to be working. I was wondring which kernel module you are using? I was looking through your patch file and I can't seem to find a mention of and AW9523 specific module. Also, how are you setting up the leds intended to be used with

The size of my interceptor looks like 120 x 100 mm , but Mini-ITX is 170 mm x 170 mm. Will the screws fit the holes? I'm looking at this amazon case : https://www.amazon.com/Thermaltake-Computer-Chassis-Interchangeable-CA-1B8-00S1WN-00/dp/B00M2UKGSM/ref=asc_df_B00M2UKGSM/?tag=hyprod-20&linkCode=d

I am experiencing frequent state changes of eth0 in the kernel log, the messages look like this: [514004.065607] bcmgenet fd580000.ethernet eth0: Link is Down [514007.137676] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx During the course of the last 24 hours I got

Over on https://www.axzez.com/forum/interceptor-carrier-board/40-pin-ffc-gpio (topic is closed or I'd reply there), I see that the FFC connectors expose I2C and some GPIO pins. I'd be interested in using them for some uses other than network interfaces. Could someone (@Bill Nagel perhaps?) post th

Hey axzez team! Thanks for your building this great product. I have recently started tinkering with the interceptor and started looking into the kernel patch for 5.15 that you provide. I noticed that more recent kernels have an updated switch driver that leverages the DSA subsystem and I was wonder

I would ask if this fan is compatible with the carrier board or help me find a better cooler for cm4? Thanks