Forum Posts

Bill Kreutz
First week member
First week member
Apr 23, 2022
In Interceptor Software Use
I noticed that the OS was recently updated. What's new? If there's a change log I must have missed it.
0
1
35
Bill Kreutz
First week member
First week member
Apr 23, 2022
In Interceptor Carrier Board
Have any of you found an enclosure that fits the Interceptor board nicely? With or without the adapter plate? Mine is working great, but looks like a heap of hard drives and wires on my desk. Recommendations would be greatly appreciated.
0
11
138
Bill Kreutz
First week member
First week member
Mar 28, 2022
In Interceptor Carrier Board
For anyone else struggling to get WiFi working on the Interceptor board, here's what worked for me: Some of these steps may be unnecessary, I wish I took better notes while I worked on this and could spare you some potentially unneeded steps, but this should work. From a clean install of the Interceptor OS, plug in an ethernet cable to download the packages needed to get WiFi to work. sudo apt update -y sudo apt upgrade -y sudo apt install nano -y sudo apt install network-manager -y sudo apt install raspi-config Go ahead and take this opportunity to install anything else that you like to use to navigate Linux. With those packages installed, run the following commands: sudo systemctl stop networkd-systemd sudo systemctl disable networkd-systemd sudo systemctl enable NetworkManager A reboot would be prudent at this point. sudo reboot Once up and running again, run: sudo nmtui Use the interface that pops up to connect to your preferred WiFi network. YMMV, but I had to also disable IPV6. You can do that from the nmtui interface. For reasons as of yet unknown, in my case, the WiFi doesn't seem to work when an ethernet cable is plugged into port A. Remove it and reboot. WiFi should work at this point. I also used sudo rasp-config between attempts. I don't think it's required, but if the steps above don't work, give it a try.
0
2
18
Bill Kreutz
First week member
First week member
Mar 25, 2022
In Interceptor Carrier Board
I've been trying with limited success to get this to work the way I want it to - the custom OS is neat, but too unfamiliar for me to be effective with. Can detailed instructions - including what platform is used to do the work- be put together instructing on how to path the kernel for the Raspberry Pi 64 bit OS?
0
5
53
Bill Kreutz
First week member
First week member
Mar 25, 2022
In Interceptor Carrier Board
The FAQ says details would be available soon- sorry if they're here and I missed them. How can we reconfigure the ethernet ports? I noticed that wpa_supplicant doesn't seem to work like it does in the Pi OS - what's the best way to set up WiFi with the Interceptor OS?
0
14
77
Bill Kreutz
First week member
First week member
Mar 23, 2022
In Interceptor Carrier Board
I support several web services for the regional emergency data network, and I try to make sure my services will remain available to incident response workers whether utility provided power is available or not. In order to do this with the Interceptor board, I'm looking at few potential options. Have any been tested? If any can be ruled out for some reason or another please let me know. https://smile.amazon.com/dp/B071P3HMNK/ref=cm_sw_r_apan_i_39K4CQK37EP7EYFEPWJG?_encoding=UTF8&psc=1 https://smile.amazon.com/dp/B09MK76452/ref=cm_sw_r_apan_i_QDBF8RHPWY8KKPN2JT5V?_encoding=UTF8&psc=1 https://smile.amazon.com/dp/B00NB6U3TS/ref=cm_sw_r_apan_i_ZEBFA84GB4H0CZ8QKR20?_encoding=UTF8&psc=1 https://www.amazon.com/dp/B08F57GKCL/ref=cm_sw_r_apan_i_WFS6P4Z1G459G9BZQFEW
0
3
54
Bill Kreutz
First week member
First week member
Mar 20, 2022
In Interceptor Carrier Board
I've installed the Axzez provided OS using Raspberry Pi Imager, and I have it hooked up to a monitor in HDMI port 0, and to a keyboard and mouse via USB ports. It's powered by the 24 pin connector from a Thermaltake PS-SPD-0500NPCWUS-W power supply. When the supply is turned on, nothing happens. I verified that the power supply seems to be working. What troubleshooting steps can I follow to try to diagnose and fix this issue?
0
12
85
 
Bill Kreutz
First week member
+4
More actions