Interceptor Software Use

I have a CM4008032. I installed the operating system from windows using Balena Etcher, getting unexpected error45. I then reflashed the operating system using Raspberry PI Imager from windows, then I tried the Raspberry Pi Imager from Debian using your current version 23.01.26.42. Each time I have g

Hi, I bought my interceptor a while ago, but its sat in the box for a while as I couldn't get a CM4. Luckily I now have one (8GB/8GB) on its way to me, so its time to dust off this project. I plan to use it to make a NAS with SSD drives and use OMV6. My question is if my end point is OMV6 should

How would I use the interceptor board with OpenWrt? I flashed the latest img to a usb stick. Resized the second partition to fill the entire drive. Then changed the cmdline.txt to the following: console=serial0,115200 console=tty1 root=PARTUUID=5452574f-02 rootfstype=squashfs,ext4 rootwait It se

I'm trying to boot my OS from a SATA SSD. If I boot from a USB stick with the interceptor OS flashed to it, what are the requirements for another OS on a SATA drive to show up in that boot menu? So I used to do this with no real problems: the interceptor OS was installed on my SSD (with OMV running

Hey, so on Raspberry Pi OS arm_freq parameter is used to specify the overclock target for the CM4. Is this possible at all with Interceptor OS? I see no /boot/config.txt

Hi, Is there a way to see the L2 forwarding (MAC address) tables on either of the switch chips (either the rtl8367 on the interceptor carrier board or the IP179h on the POE board)? I wonder if there's an swconfig get key, like "get mac" or "get mac-addr-table" or something? panda:~# swconfig dev

Dear AXZEZ Team, Thanks for your efforts on the Interceptor board, I was looking for something like this for quite some time and finally got it last week, had to ship it to a friend in USA and then ship it India. I have tried the Interceptor with AXZEZ OS image using CM4 4G+32GB eMMC and 2G+8GB eMM

I would like to make the lan ports behave more like a switch, where the router plugged in the wan port assigns the IP address to anything plugged into them instead of the dhcp server running on the board. In the FAQ it says "These ports can be reconfigured with the following commands" but then give

I have a DNS server on my network that I run everything through. It is a PiHole running in a Docker container for anyone interested. The Interceptor should have picked up this DNS server when it got its DHCP, but it seemed to have not. So I used resolvectl to manually set it, and it still isn't wor

I noticed that the OS was recently updated. What's new? If there's a change log I must have missed it.

Hello, Fellow Interceptor user here. Don't worry, this is not a question, it's the answer I came up with ;) TLDR: check my project on GitHub [1]! Intro / motivation: I was having the same dilemma as some of the other users about preparing a custom distro for the Interceptor board (preferably, a m

I have two boards each with a new CM4 Rpi with OMV6 and 2 WD Red 10TB hard drives. Trying to use it as a secondary backup for my small NAS. The data set I need to put on it is less than 4TB. I am running wired ethernet. OMV says the drives are in good order. I am mapping the drive onto a Windows ma

if you purchase a CM4 from you guys does it come pre-flashed with the Interceptor O/S? Thank you!

Hi, cannot find SSD , in Ubuntu everything auto mounts. Do I need to mount this manually or through fstab ? The install works and so does gparted .

I've set up my interceptor with the Axzez OS, its been running very fine for a couple of months now. I'm only using the WAN ethernet port of the Axzez board. The setup is such that the main OS is on an SSD (/dev/sda) and a RAID1 running on /dev/sdb & /dev/sdc does hold the main (its a NAS). My und

I was wondering how you compiled ZFS for the Interceptor OS. I would like to use the pre-built image but upgrade the ZFS kmod from 2.0 -> 2.1 (the userspace version is 2.1 already). When I download linux-headers and try to compile zfs with zfs-dkms, it's not building for the right kernel.

Where can I download the swconfig? It isn't in the download section.

I'm not able to boot the Interceptor OS from a USB thumb drive. I don't have any problems booting Raspberry Pi OS. I'm not sure what I'm missing. Please see photos for more info.

I'd like to try running a single node Rook/Ceph cluster in k3d on the interceptor just for fun. When I tried to spin up a k3d cluster I got a warning about cgroups: WARN[0058] warning: encountered fatal log from node k3d-rook-server-0 (retrying 0/10): Ptime="2022-04-27T02:23:11Z" level=fatal msg="fa